La Cornue C9MN Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non La Cornue C9MN. La Cornue C9MN Electrical Requirments Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 6
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
25
INSTALLATION
Check the appliance is electrically safe when you have nished.
Electrical Connection
When installed the range must be electrically grounded in
accordance with local codes or; in the absence of local codes
with the National Electrical Code ANSI/NFPA 70, latest edition.
In Canada the range must be installed in accordance with the
current CSA Standard C22.1 – Canadian Electrical Code Part 1.
Electrical Requirements
For personal safety, do not use an extension cord
with this appliance. Remove the house fuse or open
the circuit breaker before beginning installation.
This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or
time-delay fuse, as noted on the rating plate.
Wiring must conform to National Electric Codes. If the electric
service provided does not meet the above specications,
have a licensed electrician install an approved outlet.
Because range terminals are not accessible after range is in
position, exible service conduit or cord must be used.
Provide Proper Electrical Supply
This range must be supplied with 240 V 60 Hz, and
connected to an individual, properly grounded branch circuit
protected by a circuit breaker or time-delay fuse (16 amp).
If the electrical service provided does not meet the above
specications, it is recommended that a licensed electrician
install an approved outlet.
From January 1, 1996, the National Electric Code requires
that new construction (not existing) uses a 4-conductor
connection to an electric range.
Connecting using the supplied cord and plug
Your range is shipped with a 4-prong plug to be used in a
NEMA 14-50R receptacle.
Recommended Electrical Outlet Locations
Locate the electric supply as illustrated (Fig. 6-1).
When connecting using a NEMA 14-50R receptacle, if possible
position it so that it can be accessed through the opening
at the rear of the drawer cavity. The range can then be easily
disconnected for servicing, etc.
Plug the range power cord into a properly grounded wall
receptacle.
Connecting if the supplied cord and plug is not
suitable
To remove the electrical connection cover (Fig. 6-2), remove
the screws.
Area accessible through drawer
Gas shut-o valve
Gas supply
zone
Electrical
supply zone
Side of
range
Range gas
inlet
17”
6”
6”
7”
16”
6”
9”
4”
ArtNo.281-0008 - 900SC - Electrical connection cover
Fig. 6-1
Fig. 6-2
Vue de la page 0
1 2 3 4 5 6

Résumé du contenu

Page 1 - Electrical Connection

25INSTALLATIONCheck the appliance is electrically safe when you have nished.Electrical ConnectionWhen installed the range must be electrically ground

Page 2 - 4-Wire Conduit Installation

26INSTALLATIONCheck the appliance is electrically safe when you have nished.4-Wire Conduit InstallationDisconnect the supplied power cord from the te

Page 3 - 3-Wire Conduit Installation

27INSTALLATIONCheck the appliance is electrically safe when you have nished.3-Wire Conduit InstallationDisconnect the supplied power cord from the te

Page 4 - Gas Connection

28INSTALLATIONCheck the appliance is electrically safe and gas sound when you have nished.Gas ConnectionInstallation of this range must conform with

Page 5 - Flexible Connector

29INSTALLATIONCheck the appliance is electrically safe and gas sound when you have nished.Connect the Range to the Gas SupplyShut o the main gas sup

Page 6 - Seal the Openings

30INSTALLATIONCheck the appliance is electrically safe and gas sound when you have nished.Seal the OpeningsSeal any openings in the wall behind the r

Commentaires sur ces manuels

Pas de commentaire